Rural King RK19 Hydrostatic Operator'S Manual Download

Page: 91 / 156

5 - 8

Maintenance and service

checking and changing

frOnt axle Oil

(1) inspection

①

Pull out the dipstick, wipe its tip

and insert it again. Then, pull it

out and check that the oil level

is between the upper and lower

limits.

②

If insufficient, add oil.

※

There is one front axle oil drain

hole on each side of the front

axle.

►

Front axle

oil filler

T5O51A

Level gauge

Front axle

oil drain

plug

Upper

limit

Lower

limit

(2) changing

①

Unscrew the drain plugs on the

bottom of the axle and left/right

final cases to drain engine oil.

Since hot fluid flows out of the

engine first, be careful not to get

burnt.

②

After draining oil, tighten the oil

drain plug.

③

Add the specified amount of the

specified oil through the filler

hole.

Do not add front axle oil over

the upper limit level.

Check the front axle oil before

starting the engine or at least

in 5 minutes after the engine is

stopped.
When trying to use new oil from

a different manufacturer or oil

with different viscosity, drain

used oil completely before add-

ing new oil.

•

nOte

T19O508A

RK19-영문-05(마).indd 8

2017-05-18 오후 6:35:20

Summary of Contents for RK19 Hydrostatic





























































































































































Search results

Summary of Contents for RK19 Hydrostatic

Reviews:

Related manuals for RK19 Hydrostatic

Brands by name

Popular brands

Rural King RK19 Hydrostatic, Operator'S Manual

Search results

Summary of Contents for RK19 Hydrostatic

Reviews:

Related manuals for RK19 Hydrostatic

Brands by name

Popular brands