Rural King RK19 Hydrostatic Operator'S Manual Download

Page: 25 / 156

- 2

SAFeTY PReCAUTIONS

14. Never remove or modify the

seat belt.

15. Never remove, modify or repair

the ROPS frame.

Please remember that a little bit of

extra care can prevent serious injury

or teath and avoid damage to your

tractor.

▶

THe FOLLOWING PReCAUTIONS

ARe SUGGeSTeD TO HeLP PRe-

VeNT ACCIDeNTS

A careful operator is the best oper-

ator. Most accidents can be avoid-

ed by observing certain precautions.

Read and take the following precau-

tions before operating the tractor to

prevent accidents.
Tractor should be operated only

by those who are responsible and

properly trained to do so.

<THe TRACTOR>

1. Read the operator’s manual care-

fully before using the tractor. Lack

of operating knowledge can lead

to accidents.

2. Use an approved rollover bar and

seat belt for safe operation. Over-

turning of a tractor without a rollover

bar can result in death or injury.

3. Do not remove ROPS (Roll Over

Protective Structure). Always use

the seat belt.

4. Fiberglass canopy does not give

any protection.

5. To prevent falls, keep steps and

platform clear of mud and oil.

6. Do not permit anyone but the op-

erator to ride on the tractor. There

is no safety place for extra riders.

7. Replace all missing, illegible or

damaged safety signs.

8. Keep safety signs clean of dirt

and grease.

<SeRVICING THe TRACTOR>

1. keep the tractor in good operat-

ing condition for your safety. An

improperly maintained tractor can

be hazardous.

2. Stop the engine before perform-

ing any service on the tractor.

3. The cooling system operates un-

der pressure, which is controlled

by the radiator cap. It is danger-

ous to remove the cap while

the system is hot. First turn the

cap slowly to stop and allow the

RK19-영문-01A(안).indd 24

2017-05-19 오전 9:41:32

Summary of Contents for RK19 Hydrostatic





























































































































































Search results

Summary of Contents for RK19 Hydrostatic

Reviews:

Related manuals for RK19 Hydrostatic

Brands by name

Popular brands

Rural King RK19 Hydrostatic, Operator'S Manual

Search results

Summary of Contents for RK19 Hydrostatic

Reviews:

Related manuals for RK19 Hydrostatic

Brands by name

Popular brands