Rural King RK19 Hydrostatic Operator'S Manual Download

Page: 7 / 156

SAFeTY PReCAUTIONS

▶

GeNeRAL CONSTRUCTION

The transmission case, Engine and

Front Axle Support are bolted to-

gether to form a rigid unit.

▶

FRONT AxLe & WHeeLS

The 4WD front axle is a center-piv-

ot, reverse Eliot type. The front

wheel drive mechanism is incorpo-

rated as a part of the axle.
The front wheel drive power is taken

off the rear transmission and trans-

mitted to the differential in the front

axle where the power is divided into

right and left and to the respective

final cases.

In the final cases, the transmitted

revolution is reduced by the level

gears to drive the front wheel. The

4WD mechanism with level gears

provides wider steering and greater

durability.

▶

eNGINe

The tractors are fitted with vertical,

Water-cooled 3-cycle and spherical

chamber type YANMAR
ENGINE(3TNV74F-SDKTF2)

▶

TRANSMISSION WITH HST (HY-

DROSTATIC TRANSMISSION)

The Tractor is fitted HST with 2

Range and can be selected Speed

range by HIGH-LOW selector lever.
The Tractor has Two pedals for for-

ward/reverse control . Tractor with

Independent Power Take Off is fitted

with electro-hydraulic Clutch Assy.

The Rear PTO and Mid PTO can be

operated both or separately by a le-

ver.
RK tractors are provided with inde-

pendent disc brakes operated by

two road travel. A foot brake lever is

fitted for parking.

DeSCRIPTION

▶

ReAR AxLe & WHeeLS

This is mounted on ball bearings

and is enclosed in removable hous-

ing which are bolted to the transmis-

sion case. The rim & Disc fitted with

Rear tires are bolted to the outer

flange of Rear Axle.

▶

HYDRAULIC SYSTeM & LINK-

AGeS

Tractors are fitted with Live (i.e.

system is in operation) independent,

very touch of hydraulic System.

Three point Linkages can be used

for category 1 type of implements.

▶

STeeRING

It consists of Hydrostatic Power

steering system, which has a hy-

draulic cylinder and tandem type hy-

draulic pump.

RK19-영문-01A(안).indd 6

2017-05-19 오전 9:41:14

Summary of Contents for RK19 Hydrostatic





























































































































































Search results

Summary of Contents for RK19 Hydrostatic

Reviews:

Related manuals for RK19 Hydrostatic

Brands by name

Popular brands

Rural King RK19 Hydrostatic, Operator'S Manual

Search results

Summary of Contents for RK19 Hydrostatic

Reviews:

Related manuals for RK19 Hydrostatic

Brands by name

Popular brands