Rural King RK19 Hydrostatic Operator'S Manual Download

Page: 28 / 156

- 2

SAFeTY PReCAUTIONS

<OPeRATING THe PTO>

1. When operating PTO driven

equipment, shut off the engine

and wait until the PTO stops be-

fore getting off the tractor and

disconnecting the equipment.

2. Do not wear loose clothing when

operating the power take-off or

near rotating equipment.

3. When operating stationery PTO

driven equipment, always ap-

ply the tractor parking brake and

block the rear wheels from front

and rear side.

4. To avoid injury, always move

down flip part of PTO. Do not

clean, adjust or service PTO

driven equipment when the trac-

tor engine is running.

5. Make sure the PTO master shield

is installed at all times and al-

ways replace the PTO shield cap

when the PTO is not in use.

<DIeSeL FUeL>

1. Keep the equipment clean and

properly maintained.

2. Under no circumstances should

gasoline, alcohol or blended fu-

els be added to diesel fire or ex

plosive hazard. Such blends are

more explosive than pure gaso-

line. In a closed container, such

as a fuel tank. DO NOT USE

THESE BLENDS.

3. Never remove the fuel cap or re-

fuel the tractor with the engine

running.

4. Do not smoke while refueling or

when standing near fuel.

5. Maintain control of the fuel filler

pipe when filling the tank.

6. Do not fill the fuel tank to capaci

ty. Allow room for expansion.

7. Wipe up spilled fuel immediately.
8. Always tighten the fuel cap se-

curely.

9. If the original fuel tank cap is

lost, replace it with genuine cap.

A none approved cap may not

be safe.

10. Do not drive equipment near

open fire.

11. Never use fuel for cleaning pur-

pose.

12. Arrange fuel purchases so that

winter grade fuel are not held

over and used in the spring.

13. USE ultra low sulfur fuel only.

※

N.B: It is suggested that after

repairs if any of the Safety

D e c a l / s i g n i s p e e l e d /

defaced, the same should

be replaced immediately in

interest of your safety.

RK19-영문-01A(안).indd 27

2017-05-19 오전 9:41:33

Summary of Contents for RK19 Hydrostatic





























































































































































Search results

Summary of Contents for RK19 Hydrostatic

Reviews:

Related manuals for RK19 Hydrostatic

Brands by name

Popular brands

Rural King RK19 Hydrostatic, Operator'S Manual

Search results

Summary of Contents for RK19 Hydrostatic

Reviews:

Related manuals for RK19 Hydrostatic

Brands by name

Popular brands