Rural King RK19 Hydrostatic Operator'S Manual Download Page 61

Page: 61 / 156

2 - 1

DESCRIPTION OF TRACTOR CONTROLS

(3) Folding seatback
The seatback can be folded down

when it is raining or for long-term

storage.

Make sure to wear your seat

belt to protect yourself from a

possible rollover or crash acci-

dent.
Never adjust the seat during

driving.

•

WARNING

T19O127A

PTO

Both of the rear and mid PTO are

provided for variable utility. They

can be engaged simultaneously or

separately at same time.
The engine will not start if PTO

switch is ON position.
The engine will shutoff if the op-

erator leaves the seat with parking

brake released and PTO engaged.

►

To avoid damage of transmis-

sion and implement, do not

engage PTO with the engine

running at high speed.

•

CAUTION

Mid

T19O128B

N
Mid+Rear
N
Rear

T19O129B

PTO

RK19-영문-02(나).indd 18

2017-05-18 오후 6:22:52

Summary of Contents for RK19 Hydrostatic





























































































































































Search results

Summary of Contents for RK19 Hydrostatic

Reviews:

Rural King RK19 Hydrostatic, Operator'S Manual, Page: 61 / 156

Search results

Summary of Contents for RK19 Hydrostatic

Reviews: