manualshive.com logo in svg

Rural King RK19 Hydrostatic, Operator'S Manual, Page: 14 / 156

Share
Download
Rural King RK19 Hydrostatic Operator'S Manual Download Page 14

 - 1

SAFeTY PReCAUTIONS

T72O208A

Do not allow riders on the tractor.
Riders on tractor are subject to in-

jury such as being stuck by foreign 

objects and being thrown off of the 

tractor.

KeeP RIDeRS OFF TRACTOR

T72O209A

Handle fuel with care; it is highly 

flammable. Do not refuel the tractor 

while smoking or near open flame 

or sparks.
Always stop engine before refueling 

tractors.
Always keep your tractor clean of 

accumulated grease, and debris. Al-

ways clean up spilled fuel. 

HANDLe FUeL SAFeLY AVOID FIReS

T72O210A

Entanglement in rotating shaft can 

cause serious injury or death.
Keep  PTO  shield  in  place  at  all 

times.

Wear close fitting clothing. Stop the 

engine and be sure PTO drive is 

stopped before making adjustments, 

connections, or cleaning out PTO 

driven equipment.  

STAY CLeAR OF ROTATING SHAFTS

RK19-영문-01A(안).indd   13

2017-05-19   오전 9:41:23

Summary of Contents for RK19 Hydrostatic





























































































































































Reviews:

No comments