Rural King RK19 Hydrostatic Operator'S Manual Download | Manualshive

Page: 148 / 156

background image

11

-

WARRANTY

11

Owner's Warranty Responsibilities:

As the off-road compression-ignition engine owner, you are responsible for the performance of the required
maintenance listed in your owner's manual. ENGINE recommends that you retain all documentation, including
receipts, covering maintenance on your off-road compression-ignition engine, but ENGINE cannot deny warranty
solely for the lack of receipts, or for your failure to ensure the performance of all scheduled maintenance.
ENGINE may deny your warranty coverage if your off-road compression-ignition engine or a part has failed due
to abuse, neglect, improper maintenance or unapproved modifications.
Your engine is designed to operate on diesel fuel only. Use of any other fuel may result in your engine no longer
operating in compliance with GARB and EPA emissions requirements.
You are responsible for initiating the warranty process. You must present your engine to a ENGINE dealer as
soon as a problem exists. The warranty repairs should be completed by the dealer as expeditiously as possible.
If you have any questions regarding your warranty rights and responsibilities, or would like information on the
nearest ENGINE dealer or authorized service center, you should contact ENGINE America Corporation.

Website: www.ENGINE.com
E-mail: [email protected]
Toll free telephone number: 1-00--, 1--1-01

RK19-영문-11-보증서.indd 9

2017-05-18 오후 6:46:05

«
...
146
147
148
149
150
...
»

Summary of Contents for RK19 Hydrostatic





























































































































































Reviews:

No comments

Related manuals for RK19 Hydrostatic

Brand: Iseki Pages: 113

Brand: Winton Pages: 40

BH Generation 4

Brand: Valtra Pages: 21

SuperSpread PTO 135

Brand: PEQUEA Pages: 28

UTILIX HT Series

Brand: Zetor Pages: 154

6400 BROCHURE 100-170

Brand: MASSEY FERGUSON Pages: 36

10520 TURBO INTERCOOLER

Brand: Zetor Pages: 236

Brand: Soucy Pages: 73

Brand: Knape & Vogt Pages: 3

Brand: Knape & Vogt Pages: 6

Brand: Burco Pages: 8

Brand: Kubota Pages: 205

Brand: AGCO Pages: 6

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands