Rural King RK19 Hydrostatic Operator'S Manual Download | Manualshive

Page: 144 / 156

background image

11

-

WARRANTY

11

2. EMISSION SYSTEM WARRANTY

ENGINE CO., lTD. EMISSION CONTROl SYSTEM WARRANTY- USA ONlY

Your Warranty Rights and Obligations:

The  California Air  Resources  Board  (GARB),  the  United  State  Environmental  Protection Agency  (EPA)  and
ENGINE  CO.,  LTD.  hereafter  referred  to  as  ENGINE,  are  pleased  to  explain  the  emission  control  system
warranty  on  your  industrial  compression-ignition  engine.  In  California,  model  year  000  or  later  off-road
compression-ignition engines must be designed, built and equipped to meet the State's stringent anti-smog In
all states, 1 and later non-road compression-ignition engines must be designed, built and equipped to meet
the United States EPA emissions standards. ENGINE must warrant the emission control system on your engine
for the periods of time listed below provided there has been no abuse, neglect or improper maintenance of your
engine.
Your emission control system may include parts such as the fuel injection system, the air induction system, the
electronic control system, EGR (Exhaust Gas Recirculation) system and the diesel particulate filter system. Also
included may be hoses, belts, connectors and other emission-related assemblies.
Where a warrantable condition exists, ENGINE will repair your off-road compression-ignition engine at no charge
to you including diagnosis, parts and labor.

RK19-영문-11-보증서.indd 5

2017-05-18 오후 6:46:04

«
...
142
143
144
145
146
...
»

Summary of Contents for RK19 Hydrostatic





























































































































































Reviews:

No comments

Related manuals for RK19 Hydrostatic

Brand: Claas Pages: 31

Marathon RAMJET Signature J-250SC

Brand: Dover Pages: 47

Brand: Krone Pages: 84

Brand: Hagie Pages: 97

Brand: Hagie Pages: 120

Brand: WALTERSCHEID Pages: 7

Brand: Valtra Pages: 19

Brand: MAGNATRAC Pages: 86

Mounted 214 LH Series

Brand: Ransomes Pages: 124

Vario 900 Series

Brand: FENDT Pages: 51

Brand: Countax Pages: 24

Brand: GE Pages: 26

MONOGRAM ZCG3300 WW

Brand: GE Pages: 16

Brand: Yanmar Pages: 4

Brand: Poulan Pro Pages: 30

Brand: McGill Pages: 30

Brand: Grillo Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands