Rural King RK19 Hydrostatic Operator'S Manual Download | Manualshive

Page: 149 / 156

background image

11

- 10

WARRANTY

■

EMISSION-RElATED INSTAllATION INSTRUCTIONS (REF)

Failing to follow these instructions when installing a certified engine in a piece of non-road equipment violates
Federal Law (0 CFR10.10()), subject to fines or other penalties as described in the clean air act.

Installation of Non-road Engines into Equipment

To ensure engines operate under the certified configurations, ENGINE has established defined application
requirements when installing any certified engine into a piece of equipment. The instructions outlined below are
included in our certification process and any failure to comply will be considered tampering.
ENGINE certifies engines to operate under variable speed or constant speed conditions. Engines certified as
constant speed are prohibited from installation into variable speed applications. The emission control information
label will identify an engine certified as constant speed.

Allowable Air Intake Restriction and Exhaust Back Pressure

Resistance to intake airflow and exhaust gas flow is generated in the intake and exhaust systems.
Exceeding the limitations will affect the operation of an engine and its certified configuration. Refer to the
installation requirements and limitations of the TNV series Application Manual for the engine being equipped with
these systems.

RK19-영문-11-보증서.indd 10

2017-05-18 오후 6:46:05

«
...
147
148
149
150
151
...
»

Summary of Contents for RK19 Hydrostatic





























































































































































Reviews:

No comments

Related manuals for RK19 Hydrostatic

Brand: Kellfri Pages: 12

Brand: Eagle Pages: 83

Monogram ZCGP150PII

Brand: GE Pages: 2

MONOGRAM ZCGP150LII

Brand: GE Pages: 2

Brand: GE Pages: 24

Brand: GE Pages: 24

Monogram ZCGS150PSS

Brand: GE Pages: 2

Techstar CVT MT525B Series

Brand: Challenger Pages: 248

Brand: McCulloch Pages: 60

Brand: Winton Pages: 24

Brand: Tennant Pages: 36

Brand: Cub Cadet Pages: 61

Groom Master II 88009

Brand: Jacobsen Pages: 86

Brand: Valtra Pages: 31

Brand: Valtra Pages: 41

Brand: Kubota Pages: 25

Brand: Kubota Pages: 90

Brand: Jenn-Air Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands