Rural King RK19 Hydrostatic Operator'S Manual Download

Page: 11 / 156

- 10

SAFeTY PReCAUTIONS

To select Seat position, move Ad-

justing lever and slide Seat closer to

or away from Dash panel and con-

trols.

Check whether the seat prop-

erly locked in its position be-

fore driving the tractor.

•

DANGER

Always use the seat belt

when the ROPS is installed.

Do not use the seat belt if a

foldable ROPS is down or

there is no ROPS. Check the

seat belt regularly and re-

place if frayed or damaged.

•

DANGER

6. SAFeTY INSTRUCTIONS

T74O201A

This symbol means ATTENTION!

YOUR SAFETY IS INVOLVED. The

message that follows the symbol

contains important information about

safety. Carefully read the message.

ReCOGNIZe SAFeTY INFORMATION

SIGNAL WORDS

DANGER

WARNING

CAUTION

T74O202B

A signal word "DANGER, WARN-

ING OR CAUTION" is used with

safety alert symbol. DANGER identi-

fies the most serious hazards. Safe

ty signs with signal Word "DANGER

OR WARNING" are typically near

specific hazards. General precau-

tions are listed on CAUTION safety

signs.

RK19-영문-01A(안).indd 10

2017-05-19 오전 9:41:21

Summary of Contents for RK19 Hydrostatic





























































































































































Search results

Summary of Contents for RK19 Hydrostatic

Reviews:

Related manuals for RK19 Hydrostatic

Brands by name

Popular brands

Rural King RK19 Hydrostatic, Operator'S Manual

Search results

Summary of Contents for RK19 Hydrostatic

Reviews:

Related manuals for RK19 Hydrostatic

Brands by name

Popular brands