Rural King RK19 Hydrostatic Operator'S Manual Download Page 46

Page: 46 / 156

2 -

DESCRIPTION OF TRACTOR CONTROLS

T19O108B

OFF

Start

MAIN SWITCH

It is used to start and stop the en-

gine.



"OFF" position

The ignition key can be inserted

and removed in this position.

When turning the switch to the

OFF position with the engine

running, the engine is stopped.



"ON" position

The engine is kept running and

the switch is energized in this

position.

►



"START" position

The engine can be started in

this position. When releasing the

key, the switch is returned to the

"ON" position.



"GLOW" position

The engine's combustion chamber

is pre-heated in this position.

T19O109A

TACHOMETER

It displays the revolution of the en-

gine or PTO shaft per minute.

►

GLOW

RK19-영문-02(나).indd 3

2017-05-18 오후 6:22:37

Summary of Contents for RK19 Hydrostatic





























































































































































Search results

Summary of Contents for RK19 Hydrostatic

Reviews:

Rural King RK19 Hydrostatic, Operator'S Manual, Page: 46 / 156

Search results

Summary of Contents for RK19 Hydrostatic

Reviews: