Rural King RK19 Hydrostatic Operator'S Manual Download Page 117

Page: 117 / 156

7 -

TROUBLESHOOTING

2. BRakE SYSTEM

TROUBLE

PROBaBLE caUSE

SOLUTION

Brake

The brake won't operate.

Also, only one-side brake

operates

Excessive brake pedal play

•

Adjust the play

•

Worn or burnt liner

•

Have it repaired by workshop

•

Different play amount on left and

•

Set the left and right play amount the same

•

3. STEERING SYSTEM

TROUBLE

PROBaBLE caUSE

SOLUTION

Steering system

The steering wheel

feels heavy

The steering wheel vi-

brates

Improper toe-in

•

Adjust

•

Incorrect tire inflation pressure

•

Set the left and right tires to the same specified pressure

•

Vibration from each connection

•

Tighten or replace connection

•

The free movement of

the steering wheel is

excessive

Worn steering wheel shaft

•

Have it repaired by workshop

•

Worn metal parts

•

Have it repaired by workshop

•

Free play from each connection

•

Tighten

•

RK19-영문-07(사).indd 6

2017-05-19 오전 9:48:58

Summary of Contents for RK19 Hydrostatic





























































































































































Search results

Summary of Contents for RK19 Hydrostatic

Reviews:

Rural King RK19 Hydrostatic, Operator'S Manual, Page: 117 / 156

Search results

Summary of Contents for RK19 Hydrostatic

Reviews: