Rural King RK19 Hydrostatic Operator'S Manual Download Page 95

Page: 95 / 156

5 - 1

Maintenance and service

7. checking and cleaning air cleaner

Check and clean the air cleaner ac-

cording to the following instructions:

< cautions for inspection and

service of air cleaner >

(1) Use the standard element and fil

ter and do not apply oil on them.

() Remove any dust in the cover

thoroughly.

() Install it firmly so that dust does

not enter below the cover.

() Never drive with the element and

filter removed.

Do not hit the element with

a rock or concrete during its

cleaning.
Make sure to install the element

firmly.

Tighten each part of the air

cleaner securely to block dust

completely.

•

nOte

T5O50A

Air cleaner body Element

vacuuM valve cleaning

Pull out the valve with a hand and

remove dust from its inside. If it

is dirty or watery, wipe it with a

dry rag thoroughly before fitting it

again.

►

•

air cleaner cleaning

①

Blow compressed air from the

inside toward the outside of the

element. Keep proper distance

between the air nozzle and ele-

ment.

air cleaner replacing

After cleaning the element 5 times

or if it is damaged, replace it with a

new one.

►

RK19-영문-05(마).indd 12

2017-05-18 오후 6:35:24

Summary of Contents for RK19 Hydrostatic





























































































































































Search results

Summary of Contents for RK19 Hydrostatic

Reviews:

Rural King RK19 Hydrostatic, Operator'S Manual, Page: 95 / 156

Search results

Summary of Contents for RK19 Hydrostatic

Reviews: