Rural King RK19 Hydrostatic Operator'S Manual Download Page 53

Page: 53 / 156

2 - 10

DESCRIPTION OF TRACTOR CONTROLS

(9) Coolant temperature warning lamp

If this lamp comes on, coolant

is overheated.

Coolant temperature warning lamp

When the coolant temperature

warning lamp comes on, cool-

ant is overheated so check the

coolant.

•

NOTE

PTO ON/OFF SWITCH

PTO ON/OFF switch is situated on

the right hand side on the instru-

ment panel and can be identified

easily with its built in yellow colored

indicator.
When the switch is pushed down

to start the PTO indicator glows to

indicate that the switch and the PTO

are in ON position.
If the switch is pushed down and

turn counter clock wise the indicator

goes off signaling that the PTO is

OFF.

►

PTO ON/OFF

switch

T19O116A

(10) Engine warning lamp It comes on

when the engine is malfunctioning.

Engine warning lamp

When Engine warning lamp is

it, ensure that you operator the

tractor only after the engine

RPM reaches at the normal

speed if this instruction is not

kept, it may cause a perfor-

mance degradation or accident

due to a system error.

•

CAUTION

RK19-영문-02(나).indd 10

2017-05-18 오후 6:22:43

Summary of Contents for RK19 Hydrostatic





























































































































































Search results

Summary of Contents for RK19 Hydrostatic

Reviews:

Rural King RK19 Hydrostatic, Operator'S Manual, Page: 53 / 156

Search results

Summary of Contents for RK19 Hydrostatic

Reviews: