Rural King RK19 Hydrostatic Operator'S Manual Download

Page: 63 / 156

2 - 20

DESCRIPTION OF TRACTOR CONTROLS

MID PTO SPEED

2.500 RPM

PTO

safety

cover

Rear PTO shaft Cap

PTO SHAFT CAP

When the PTO shaft is not in use,

grease the PTO shaft and install the

cap to it.

►

It is dangerous to use an imple-

ment at a high speed if it is de-

signed to be operated at a low

speed.
Before using an implement,

make sure to read its owner's

manual.

•

CAUTION

DANGER

If caught by the PTO shaft, a

severe injury or even death

can occur.
Stay out of the PTO shaft

while it is rotating.
When the PTO shaft is not

in use, place the cap over it.

Also, never remove the PTO

safety cover.

•

T19O131A

5. Turn on the PTO switch.
6. Increase engine speed to desired

speed.

RK19-영문-02(나).indd 20

2017-05-18 오후 6:22:54

Summary of Contents for RK19 Hydrostatic





























































































































































Search results

Summary of Contents for RK19 Hydrostatic

Reviews:

Related manuals for RK19 Hydrostatic

Brands by name

Popular brands

Rural King RK19 Hydrostatic, Operator'S Manual

Search results

Summary of Contents for RK19 Hydrostatic

Reviews:

Related manuals for RK19 Hydrostatic

Brands by name

Popular brands