Rural King RK19 Hydrostatic Operator'S Manual Download

Page: 19 / 156

- 1

SAFeTY PReCAUTIONS

eMeRGeNCY exITS

If exit from the cab side doors is

blocked (following an accident or ve-

hicle overturn) the alternative safety

exits are indicated by decals.

The possible safety exits are:
• Rear window hatch (All tractors)
• Front window (for versions with

openable front window).

T74O223A

Never let anyone get in the loader

and use the loader as a workbench.

Otherwise, it may lead to a fatal in-

jury or even death.

SAFeTY PReCAUTIONS WHeN USING THe LOADeR

Do not stand under the lifted load-

er or get close to it. Also, lower the

loader arm onto the ground before

leaving the tractor. Otherwise, it may

lead to a fatal injury or even death.

T74O226A

T74O225A

RK19-영문-01A(안).indd 18

2017-05-19 오전 9:41:27

Summary of Contents for RK19 Hydrostatic





























































































































































Search results

Summary of Contents for RK19 Hydrostatic

Reviews:

Related manuals for RK19 Hydrostatic

Brands by name

Popular brands

Rural King RK19 Hydrostatic, Operator'S Manual

Search results

Summary of Contents for RK19 Hydrostatic

Reviews:

Related manuals for RK19 Hydrostatic

Brands by name

Popular brands