Raymarine A65, Installation And Operation Instructions Manual

Page: 46 / 308

Digital radar cables
You will need a dedicated radar power and data digital cable and
SeaTalk
hs network cables to connect your scanner to your system.
Connection Required cable
Radar scanner to power supply and
Raymarine network switch. Power and data digital cable. For
longer cable runs, extensions are
available in a variety of lengths.
Raymarine network switch to
multifunction display. SeaTalk hs network cables, available in
a variety of cable lengths.
Radar power and data digital cables
These cables contain the wires for a scanner's power and data
connections.
Cable Part number
5 m (16.4 ft) Power and data digital
cable A55076D
10 m (32.8 ft) Power and data digital
cable A55077D
15 m (49.2 ft) Power and data digital
cable A55078D
25 m (82.0 ft) Power and data digital
cable A55079D
Note: The maximum length for the radar power and data digital
cable (including any extensions) is 25 m (82 ft).
Radar power and data digital extension cables
These cables extend the power and data digital cables for a
scanner's power and data connections.
Cable Part number
2.5 m (8.2 ft) Power and data digital
cable A92141D
5 m (16.4 ft) Power and data digital
cable A55080D
10 m (32.8 ft) Power and data digital
cable
A55081D
Note: The maximum length for the radar power and data digital
cable (including any extensions) is 25 m (82 ft).
Sonar connection
A sonar connection is required for fishfinder applications.
There are 2 types of connection required for fishfinder applications:
• Sonar module connection — converts the sonar signals
provided by the sonar transducer into data suitable for a marine
electronics system. The sonar variant multifunction displays
feature a built-in sonar, enabling you to connect the display
directly to a compatible sonar transducer. Non-sonar variants
require a connection to an external Raymarine sonar module.
Internal and external sonars require a connection to a compatible
sonar transducer.
• Sonar transducer connection — provides sonar signals to the
sonar module.
Sonar module connection
SeaTalk
hs
/ RayNet
SeaTalk
hs
/ RayNet
D12255-1
1
2
3
4
1. Rear connector panel of multifunction display (Non-sonar
variant).
2. Raymarine network switch.
3. Raymarine sonar module.
4. RayNet cable.
The multifunction display can be used with the following Raymarine
sonar modules:
• CP450C
• DSM300
• DSM30
Note: You can also connect a sonar variant multifunction display
to a Raymarine sonar module. This is useful in circumstances
where you need a higher powered sonar module for example.
You can only use one sonar transducer at any one time.
Sonar connected directly to the display
On smaller systems (with only one display and no other SeaTalk hs /
RayNet devices) the sonar module may be connected directly to the
display without using a Raymarine network switch.
Note: You must ensure that the cable ends connected into
the display and sonar module have a locking / weather-tight
mechanism.
Compatible sonar transducers
The multifunction display is compatible with the following sonar
transducers:
• Raymarine P48.
• Raymarine P58.
• Minn Kota transducers Sonar variant Raymarine displays only),
via optional A62363 adaptor cable.
• Any 600 watt sonar-compatible transducer, via optional E66066
adaptor cable.
Sonar transducer connection — Sonar variant multifunction
displays
2
D 12256-1
1
3
1. Rear connector panel of multifunction display (Sonar variant).
2. Sonar transducer cable.
3. Sonar transducer.
46 New a Series / New c Series / New e Series