Qiagen PyroMark Q24 MDx Page 11 User Manual Download

Page: 11 / 104

Safety Information

PyroMark Q24 MDx User Manual 01/2016

1-5

WARNING

Sharp needles

Do not touch the sharp needles at the bottom of the

reagent cartridge. Handle the needles with care. Small
particles and fibers may obstruct the needles.

CAUTION

Light guide maintenance

Use lint free tissues to clean the space between the heating

block and the light guide block inside the instrument. Do
not use paper tissues.

1.6

Heat hazard

WARNING

Hot surface

The plate holder and the heating block (for annealing) can

reach temperatures of up to 80°C (176°F). Avoid touching
them when they are hot.

CAUTION

Risk of overheating

To ensure proper ventilation, maintain a minimum

clearance of 10 cm (3.94 in.) at the sides and rear of the
PyroMark Q24 MDx Instrument.
Slits and openings that ensure the ventilation of the

PyroMark Q24 MDx Instrument must not be covered.

1.7

Consumables

CAUTION

Unsupported consumables

Do not connect or use any consumables, accessories, or
external equipment other than that specified.

Summary of Contents for PyroMark Q24 MDx









































































































Search results

Summary of Contents for PyroMark Q24 MDx

Reviews:

Related manuals for PyroMark Q24 MDx

Brands by name

Popular brands

Qiagen PyroMark Q24 MDx, User Manual

Search results

Summary of Contents for PyroMark Q24 MDx

Reviews:

Related manuals for PyroMark Q24 MDx

Brands by name

Popular brands