Qiagen PyroMark Q24 MDx Page 65 User Manual Download

Page: 65 / 104

Maintenance

PyroMark Q24 MDx User Manual 01/2016

6-7

Procedure

Ensure that no vacuum is applied to the vacuum prep

tool, i.e., the vacuum switch is closed (Off), and the
vacuum pump is switched off.

Disconnect the vacuum pump from the mains power.

Remove the tool from the tubing.

Loosen the four screws using the 2 mm Allen key

supplied with the system.

Pull out the old filter probes.

Gently insert new filter probes without pressing on the

filter tips.

Fasten the four screws and reconnect the vacuum pump

to the mains power.

6.3.3

Replacing the rubber seal

If the filter probes are loose and/or fall out, there are two
possible causes:



The four screws are not tight enough



The rubber seal needs to be replaced

If the rubber seal needs to be replaced, the following items
are required:



Powder-free gloves,



2 mm Allen key (supplied with the system)



New rubber seal (QIAGEN)

Summary of Contents for PyroMark Q24 MDx









































































































Search results

Summary of Contents for PyroMark Q24 MDx

Reviews:

Related manuals for PyroMark Q24 MDx

Brands by name

Popular brands

Qiagen PyroMark Q24 MDx, User Manual

Search results

Summary of Contents for PyroMark Q24 MDx

Reviews:

Related manuals for PyroMark Q24 MDx

Brands by name

Popular brands