Qiagen PyroMark Q24 MDx Page 25 User Manual Download | Manualshive

Page: 25 / 104

background image

Installation Procedures

PyroMark Q24 MDx User Manual 01/2016

4-1

4

Installation Procedures

4.1

System delivery and installation

The unpacking and installation of the PyroMark Q24 MDx is

carried out by a certified QIAGEN Field Service Specialist. A
person who is familiar with your laboratory and computer
equipment should be present during the installation.

The following items are delivered:



PyroMark Q24 MDx Instrument (including two USB sticks)



PyroMark Q24 MDx Vacuum Workstation (purchased

separately)



PyroMark Q24 MDx User Manual



PyroMark Q24 MDx Software User Guide



PyroMarkQ24 Plate Holder

Reagents and other accessories can be ordered separately,
visit www.qiagen.com/products/PyromarkQ24MDx.aspx.

4.2

Requirements

Site

The PyroMark Q24 MDx Instrument and PyroMark Q24 MDx

Vacuum Workstation must be located out of direct sunlight,
away from heat sources, and away from sources of vibration
and electrical interference. Refer to Appendix A for the

operating conditions (temperature and humidity). The site of
installation should be free of excessive drafts, excessive

moisture, excessive dust, and not subject to large
temperature fluctuations.
Refer to Appendix A for the weight and dimensions  of the
PyroMark Q24 MDx Instrument and  PyroMark Q24 MDx

Vacuum Workstation.

«
...
23
24
25
26
27
...
»

Summary of Contents for PyroMark Q24 MDx









































































































Reviews:

No comments

Related manuals for PyroMark Q24 MDx

Brand: GE Pages: 24

Brand: Haag-Streit Pages: 18

Brand: Haag-Streit Pages: 20

Brand: V-TEK Pages: 2

Brand: V-TEK Pages: 112

Brand: Rane Pages: 38

Brand: Kartsana Pages: 36

Brand: Landoll Pages: 70

Brand: Landice Pages: 19

Brand: Landice Pages: 7

Brand: natus Pages: 20

Dantec Keypoint G4

Brand: natus Pages: 42

Brand: natus Pages: 149

Brand: Nektar Pages: 12

Brand: Vatech Pages: 137

Brand: Vatech Pages: 68

Brand: Varytec Pages: 52

Brand: YASKAWA Pages: 81

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands