Qiagen PyroMark Q24 MDx Page 67 User Manual Download

Page: 67 / 104

Maintenance

PyroMark Q24 MDx User Manual 01/2016

6-9

Disconnect the vacuum pump from the mains power.

Remove the broken tubing at one end and empty any

liquid waste into an empty beaker.

Disconnect the other end of the tubing and discard the

tubing and any liquid waste.

Cut the new vacuum tubing into three pieces and

assemble it. Ensure that the tubing is connected to the
pump’s “Vacuum” fitting.

Reconnect the vacuum pump to the mains power.

6.3.5

Replacing the waste filter

If the waste filter is wet (e.g., if the waste container is full), no

vacuum is attained and the filter must be replaced.
Be sure to observe all national, state, and local environmental
regulations for the disposal of laboratory waste.

The following items are required:



New waste filter



Beaker

Note

: Two waste filters are supplied with the vacuum

workstation. Filters can be ordered at www.millipore.com

(Millipore Millex-FG50 Filter Unit, cat. no. SLFG05010).

Procedure

Ensure that no vacuum is applied to the vacuum prep
tool, i.e. the vacuum switch is closed (Off), and the

vacuum pump is switched off.

Disconnect the vacuum pump from the mains power.

Remove the tubing from the filter fittings and empty any
liquid waste into a beaker.

Discard the filter.

Push the tubing onto the fittings of the new filter.

If necessary, empty the waste container.

Note

: The cap can be removed without disconnecting

the tubing.

Reconnect the vacuum pump to the mains power.

Summary of Contents for PyroMark Q24 MDx









































































































Search results

Summary of Contents for PyroMark Q24 MDx

Reviews:

Related manuals for PyroMark Q24 MDx

Brands by name

Popular brands

Qiagen PyroMark Q24 MDx, User Manual

Search results

Summary of Contents for PyroMark Q24 MDx

Reviews:

Related manuals for PyroMark Q24 MDx

Brands by name

Popular brands