Qiagen PyroMark Q24 MDx User Manual Download

Page: 46 / 104

Operating Procedures

5-18

PyroMark Q24 MDx User Manual 01/2016

5.5.1

Instrument software

The instrument is controlled via the six buttons underneath the
screen.

Runs are started and monitored through the instrument
software. During processing of a run, the software displays

the following information:

Run name

Selected well

Current time

Instrument status

Pyrogram

Warning messages

Estimated remaining run time
(hh:mm)

5.5.2

Starting the instrument

Before switching on the instrument, ensure that the mains
plugs are connected to properly grounded (earthed)
mains outlets with the correct voltage and frequency and

that mains plugs are easily accessible in case the
instrument needs to be disconnected quickly from mains
power.

Switch on the instrument. The power switch is located at
the rear of the instrument (see image in Section 3.4).

Summary of Contents for PyroMark Q24 MDx









































































































Search results

Summary of Contents for PyroMark Q24 MDx

Reviews:

Related manuals for PyroMark Q24 MDx

Brands by name

Popular brands

Qiagen PyroMark Q24 MDx, User Manual

Search results

Summary of Contents for PyroMark Q24 MDx

Reviews:

Related manuals for PyroMark Q24 MDx

Brands by name

Popular brands