Qiagen PyroMark Q24 MDx Page 27 User Manual Download

Page: 27 / 104

Installation Procedures

PyroMark Q24 MDx User Manual 01/2016

4-3

site. Mains supply voltage fluctuations are not to exceed 10%
of nominal supply voltages.

Grounding requirements

To protect operating personnel, the PyroMark Q24 MDx
Instrument must be correctly grounded (earthed). The

PyroMark Q24 MDx Instrument is equipped with two 3-
conductor AC power cords. To preserve this protection
feature, do not operate the PyroMark Q24 MDx Instrument

from AC power outlets that have no ground (earth)
connection.

4.3

Installation of the analysis software

4.3.1

Installing or upgrading PyroMark Q24 MDx
Software

Note

: If the computer is connected to a network, network

policy settings may prevent you from completing this
procedure. For more information, contact your system
administrator.
1.

Ensure that the computer meets the minimum
requirements; see Section 3.6.

Close any programs running on the computer.

Insert the PyroMark Q24 MDx Software CD into the CD drive.

In the CD menu, click “Install PyroMark Q24 MDx

Software”.
If the CD menu does not appear automatically:



Select “(My) Computer” in the Windows “Start”

menu.



Right-click the CD drive with the software CD and
select “Open”.



Double-click the file

autorun.exe

Follow the instructions that appear in the “Setup Wizard”.

Note

: If .NET Framework 3.5 has to be installed

(installation is prompted by the “Setup Wizard”), the

installation has to be restarted when the .NET Framework
installation has been completed, i.e., open the CD menu

Summary of Contents for PyroMark Q24 MDx









































































































Search results

Summary of Contents for PyroMark Q24 MDx

Reviews:

Related manuals for PyroMark Q24 MDx

Brands by name

Popular brands

Qiagen PyroMark Q24 MDx, User Manual

Search results

Summary of Contents for PyroMark Q24 MDx

Reviews:

Related manuals for PyroMark Q24 MDx

Brands by name

Popular brands