Qiagen PyroMark Q24 MDx Page 63 User Manual Download

Page: 63 / 104

Maintenance

PyroMark Q24 MDx User Manual 01/2016

6-5

6.3

Maintenance of the PyroMark Q24 MDx

Vacuum Workstation

WARNING

Hazardous chemicals

[W6]

The Denaturation Solution used with the vacuum

workstation contains sodium hydroxide, which is irritating
to eyes and skin.
Always wear safety glasses, gloves, and a lab coat.

The responsible body (e.g., laboratory manager) must take
the necessary precautions to ensure that the surrounding
workplace is safe and that the operators are not exposed

to hazardous levels of toxic substances (chemical or
biological) as defined in the applicable Material Safety

Data Sheets (MSDSs) or OSHA,* ACGIH,

†

or COSHH

‡

documents.
For more information, visit

www.qiagen.com/support/msds.aspx.
Venting for fumes and disposal of wastes must be in
accordance with all national, state, and local health and

safety regulations and laws.

* OSHA: Occupational Safety and Health Administration (United States of America).

†

ACGIH: American Conference of Government Industrial Hygienists (United States of America).

‡

COSHH: Control of Substances Hazardous to Health (United Kingdom).

6.3.1

Cleaning the PyroMark Q24 MDx Vacuum
Workstation

If the vacuum workstation needs to be cleaned to remove

dust and spillage, follow the instructions below.

The following items are required:



Powder-free gloves



High-purity water (Milli-Q

18.2 MΩ x cm or equivalent)



A mild detergent (if necessary)



Clean, lint-free cloths

Summary of Contents for PyroMark Q24 MDx









































































































Search results

Summary of Contents for PyroMark Q24 MDx

Reviews:

Related manuals for PyroMark Q24 MDx

Brands by name

Popular brands

Qiagen PyroMark Q24 MDx, User Manual

Search results

Summary of Contents for PyroMark Q24 MDx

Reviews:

Related manuals for PyroMark Q24 MDx

Brands by name

Popular brands