Qiagen PyroMark Q24 MDx User Manual Download

Page: 20 / 104

General Description

3-2

PyroMark Q24 MDx User Manual 01/2016

ATP sulfurylase quantitatively converts PPi to ATP in the

presence of adenosine 5' phosphosulfate.

This drives the conversion of luciferin to oxyluciferin by

luciferase, generating visible light in amounts

proportional to the amount of ATP. Light is detected
using charged coupled devices (CCDs) and seen as a
peak in the Pyrogram

. Each light signal is proportional

to the number of nucleotides incorporated.

Apyrase, a nucleotide-degrading enzyme, continuously

degrades unincorporated nucleotides and ATP. When

degradation is complete, another nucleotide is added.

Nucleotides are added one at a time.

Note

: Deoxyadenosine alfa-thio triphosphate (dATP

is used instead of natural deoxyadenosine triphosphate

(dATP) since it is used efficiently by the DNA polymerase,
but not recognized by the luciferase.

As the process continues, the complementary sequence is

built up and the nucleotide sequence is determined from
the peak in the Pyrogram.

Summary of Contents for PyroMark Q24 MDx









































































































Search results

Summary of Contents for PyroMark Q24 MDx

Reviews:

Related manuals for PyroMark Q24 MDx

Brands by name

Popular brands

Qiagen PyroMark Q24 MDx, User Manual

Search results

Summary of Contents for PyroMark Q24 MDx

Reviews:

Related manuals for PyroMark Q24 MDx

Brands by name

Popular brands