Qiagen PyroMark Q24 MDx Page 28 User Manual Download

Page: 28 / 104

Installation Procedures

4-4

PyroMark Q24 MDx User Manual 01/2016

(see step 4) and click “Install PyroMark Q24 MDx
Software”.

When the software has been successfully installed, click

“Exit Setup” in the CD menu.

Please use Windows Update

(www.update.microsoft.com) to check for any critical

updates to the .NET Framework 3.5.

To view reports generated by PyroMark Q24 MDx Software
in PDF format, a PDF reader must be installed on the
computer. Adobe Reader can be downloaded at

www.adobe.com.

4.3.2

Uninstalling PyroMark Q24 MDx Software

Select “Control Panel” in the Windows “Start” menu.

In the “Control Panel”, click “Uninstall a program” under

the Programs category.

In the list of programs, select “PyroMark Q24”.

Click “Uninstall”.

Repeat steps 3 and 4 for PyroMark Launcher.

Summary of Contents for PyroMark Q24 MDx









































































































Search results

Summary of Contents for PyroMark Q24 MDx

Reviews:

Related manuals for PyroMark Q24 MDx

Brands by name

Popular brands

Qiagen PyroMark Q24 MDx, User Manual

Search results

Summary of Contents for PyroMark Q24 MDx

Reviews:

Related manuals for PyroMark Q24 MDx

Brands by name

Popular brands