Qiagen PyroMark Q24 MDx User Manual Download

Page: 64 / 104

Maintenance

6-6

PyroMark Q24 MDx User Manual 01/2016

Procedure

Ensure that no vacuum is applied to the vacuum prep

tool, i.e., the vacuum switch is closed (Off), and the
vacuum pump is switched off.

Disconnect the vacuum pump from the mains power.

Clean the worktable and the tool, except for the filter

probes, using a clean, lint-free cloth moistened with
water or a mild detergent.
Do not touch the tips of the filter probes.

Wipe the worktable and the tool, except for the filter

probes, dry using a clean, lint-free cloth.

Reconnect the vacuum pump to the mains power.

6.3.2

Testing and replacing the filter probes

Function test for filter probes

The function test for the filter probes is described in Section
5.3.1.

Replacing filter probes

Each filter probe can be replaced individually. To ensure
proper flow rate trough the filter probes, all probes should

be replaced after preparation of approximately 100 plates.

Note

: Use gloves (powder-free) to avoid contaminating the

filter probes.

The following items are required:



Powder-free gloves



2 mm Allen key (supplied with the system)



High-purity water (Milli-Q

18.2 MΩ x cm or equivalent)



New filter probes (QIAGEN)

Summary of Contents for PyroMark Q24 MDx









































































































Search results

Summary of Contents for PyroMark Q24 MDx

Reviews:

Related manuals for PyroMark Q24 MDx

Brands by name

Popular brands

Qiagen PyroMark Q24 MDx, User Manual

Search results

Summary of Contents for PyroMark Q24 MDx

Reviews:

Related manuals for PyroMark Q24 MDx

Brands by name

Popular brands