Proximus Forum 5000 User Manual Download Page 77 | Manualshive

Page: 77 / 154

background image

Special Calls/Functions

Telephoning

75

Transfer

: This removes you from the conference, while the two other

subscribers remain connected.

End conference

: This ends the conference.

Toggle

: This breaks up the conference and you can now switch between the

subscribers.

Door opener

: This activates the door opener.

Special Calls/Functions

Accepting an Appointment Call

You can save appointments with the menu item

3 Appointments

in the

MenuCard

3 Messages

.

At the appropriate time, the appointment message appears on the display
and your telephone rings for one minute with the ringer volume steadily
increasing. Press the OK key

O

once to switch the ringer signal off. Press

O

again to acknowledge the display signal. If you lift the handset during

an appointment call, a special tone indicates that the ringer signal was an
appointment call.

You can also end the appointment call with the

e

key or by lifting the

handset. Elapsed and active appointment calls are displayed in the

Info

MenuCard.

Baby Call

You can save an internal or external call number in the menu item

4 Baby call

of the MenuCard

5 Protection

. If the menu item has been activated, this

programmed call number is dialled when a specified period has expired
(default setting is five seconds after you have lifted the handset). If you begin
dialling a call number within the specified period, the baby call is cancelled.
The baby call can also be triggered by pressing the hands-free/open-
listening key

L

, a call key

g

or the headset key

K

(requirement: the

headset has to be turned on, see page 118).

Your system administrator configures the baby call period from 0 to 20
seconds for all subscribers on the Forum 500 / Forum 5000. Ask your
administrator what the current value is.

«
...
75
76
77
78
79
...
»

Summary of Contents for Forum 5000



























































































































































Reviews:

No comments

Related manuals for Forum 5000

Brand: Panasonic Pages: 104

Brand: Panasonic Pages: 32

Brand: FAAC Pages: 60

Brand: FAAC Pages: 68

Brand: Hama Pages: 75

Brand: Linak Pages: 33

Brand: Beyerdynamic Pages: 112

Brand: Telefunken Pages: 41

Brand: Bame Pages: 12

Brand: Aiwa Pages: 76

Brand: Alpine Pages: 16

Brand: babala Pages: 30

Brand: BriarTek Pages: 2

Brand: Aritech Pages: 28

Brand: GE Pages: 79

Brand: Sailor Pages: 38

Brand: Sound Projections Pages: 2

Brand: Buderus Pages: 72

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands