Paradise Datacom Quantum Installation And Operating Handbook Download Page 90

Page: 90 / 354

Quantum and Evolution Series Installation and Operating Handbook

7-61

Edit-Tx-Scrambler-Type Screen

Options:

IBS/SMS

Only available in Closed Network plus ESC (above 32kbps) and
IBS/SMS.

V.35

This self synchronizing scrambler will multiply the errors, degrading
performance.

Turbo

Only available in when the TPC FEC is selected.

OM-73

Intelsat Reed-Solomon

Only available when the Reed-Solomon FEC is selected.

Factory
default:

V.35

Description:

Controls the type of scrambler to apply. Only available when scrambler
selection is set to

Other

Edit-Tx-Scrambler-Type-V.35 Screen

Options:

Intelsat (normal)

Scrambler type:
[V.35 ]
New: V.35

V.35 scrambler type:
[Intelsat (normal)]
New: Intelsat (normal)

Summary of Contents for Quantum



































































































































































































































































































































































Search results

Summary of Contents for Quantum

Reviews:

Brands by name

Popular brands

Paradise Datacom Quantum, Installation And Operating Handbook

Search results

Summary of Contents for Quantum

Reviews:

Brands by name

Popular brands