Paradise Datacom Quantum Installation And Operating Handbook Download Page 50

Page: 50 / 354

Quantum and Evolution Series Installation and Operating Handbook

7-21

Edit-Tx-Baseband-Advanced Menu

When the user level is set to

Advanced

(see the

Edit-Unit-Advanced-User Level

screen),

this menu allows configuration of framing, timeslots and overhead.

Edit-Tx-Baseband-Advanced-Framing Menu

This menu contains the following options:

•

2048k mode

. This option is used to indicate whether a continuous 2048kbps traffic

stream is formatted as G.732 or not.

•

CAS.

This option specifies whether Channel Associated Signalling (CAS) information

is present in Timeslot 16.

•

TS order.

This controls whether timeslot reordering is allowed.

•

Drop mode.

This specifies the framing format for Drop MUX operation.

•

G732 sig.

This option controls whether CAS information is processed and routed

through the satellite.

•

T1 sig.

This specifies whether Robbed Bit Signalling (RBS) information is present in

the traffic source.

•

CRC

. This is used to specify whether the terrestrial G.732 frame contains a checksum

that should be checked for errors.

Advanced: 1:Framing
        2:Timeslots
        3:Overhead

1:2048k mode 2:CAS 3:TS order
4:Drop mode 5:G732 sig 6:T1 sig
7:CRC

Summary of Contents for Quantum



































































































































































































































































































































































Search results

Summary of Contents for Quantum

Reviews:

Related manuals for Quantum

Brands by name

Popular brands

Paradise Datacom Quantum, Installation And Operating Handbook

Search results

Summary of Contents for Quantum

Reviews:

Related manuals for Quantum

Brands by name

Popular brands