manualshive.com logo in svg

Paradise Datacom Quantum, Installation And Operating Handbook

Share
Download
Paradise Datacom Quantum Installation And Operating Handbook Download Page 144

Quantum and Evolution Series Installation and Operating Handbook 

 

 

 

7-115

 

Edit-Unit-Interface-Terrestrial-TCP Acceleration 

 

 

Options:

 

 

TCP acceleration mode 

 
This mode provides routing of non-TCP packets combined with 
acceleration of TCP packets using a Performance Enhancing Proxy (PEP) 
that overcomes performance problems associated with using standard 
TCP over satellite. 
 

 

No TCP acceleration 
 

TCP acceleration is turned off. 
 

Factory 
default:

 

No TCP acceleration mode

 

Description:

 

This option is available in routing mode. 

 

 
Edit-Unit-Interface-Terrestrial-IP Bridge Filtering Screen 

 

 

Options:

 

 

Off 

 
In this mode, the bridge will forward all traffic not destined for the local 
subnet to the default gateway if one has been specified. If the default 
gateway is a router, then this allows the router to be set up to filter data in 
whatever way is appropriate. 
 

 

On 

 

TCP accelaration: 
         [No TCP acceleleration] 
New:[No TCP accelaration]

 

Bridge filtering:[Off] 
                       1:Off 
                       2:On 

 

Summary of Contents for Quantum



































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands