manualshive.com logo in svg

Paradise Datacom Quantum, Installation And Operating Handbook

Share
Download
Paradise Datacom Quantum Installation And Operating Handbook Download Page 154

Quantum and Evolution Series Installation and Operating Handbook 

 

 

 

7-125

page checking for in-line objects such as images. These images do not 
form part of the web page and are requested separately by the web 
browser. If the web page contains multiple embedded images or objects 
then it can take multiple times the satellite round trip time to fetch these 
since browsers will typically request them serially through a single TCP 
connection  (or possibly two) to the web server. The modem will request all 
of the images in parallel so that they are available at the modem nearest 
the web browser when the browser makes the requests for the additional 
images, significantly reducing the time it takes to display a typical web 
page. It is necessary to switch the Web Proxy on only at the modem at the 
web browser side of the satellite link.  

Factory 
default:

 

Off 

 

 

Description:

 

Enables acceleration of HTTP requests.

 
 

Edit-Unit-Interface-Terrestrial-IP DNS IP Address 

 

 
Factory default:

 0.0.0.0 

 

 

Description:

 

Sets the IP address of the DNS server to be used when the Web Proxy 
in the modem is switched on. The DNS server is used to resolve the IP 
address associated with any domain name used in the web browser. 
The DNS server IP address is normally included as part of the network 
connection details on Windows PCs. 

 

 
Edit-Unit-Interface-Terrestrial-IP Encapsulation Type Screen 

 
Options:

 

 

MPE 

 
Selects Multi-Protocol Encapsulation as the protocol for encapsulating IP 
packets and Ethernet frames into MPEG2 transport stream packets for 

DNS IP addr: 
        [000.000.000.000] 
New:[000.000.000.000] 

IP encapsulation type: 
         [MPE] 
New:[ULE]    

 

 

Summary of Contents for Quantum



































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands