manualshive.com logo in svg

Paradise Datacom Quantum, Installation And Operating Handbook

Share
Download
Paradise Datacom Quantum Installation And Operating Handbook Download Page 83

Quantum and Evolution Series Installation and Operating Handbook 

 

 

 7-54

Edit-Tx-FEC-Sequential Compatibility Screen 

The following screen will be shown at this point if Sequential FEC has been selected: 

 

Options:

 

 

Off 

 

On 

Factory default:

 

Off 

 

 

Description:

  This switches the Sequential encoder/decoder to be Comstream 

compatible at R3/4. Already compatible at R1/2 (the CM701 does not 
have R7/8 available). 

 

Edit-Tx-FEC-Frame Type Screen 

The following screen may be shown at this point after the FEC has been selected (in 
DVB-S2 IP multistreaming mode then there will be one of these screens for each stream): 

 
 

 
 
Options:

 

 

Short 

 
Selects a DVB-S2 frame size of 16200 bits.
 

Comstream Seq Compatibility: [Off]                   
         

 

 

1: Off           

         

  

 

2: On

 

FEC frame size:    
           [Normal]              
  New:[Short]

 

 

Summary of Contents for Quantum



































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands