manualshive.com logo in svg

Paradise Datacom Quantum, Installation And Operating Handbook

Share
Download
Paradise Datacom Quantum Installation And Operating Handbook Download Page 159

Quantum and Evolution Series Installation and Operating Handbook 

 

 

 

7-130

 
Edit-Unit-Interface-Terrestrial-G.703 Line Length Screen 
 

 
Options:

 

 

133m 

 

266m 

 

399m 

 

533m 

 

655m 

Factory default:

 

133m 

 

 

Description:

 

Allows the signal to be pre-compensated to cope with differing lengths of 
standard `ABAM` cable. If in doubt, select option 1, less than 133 feet by 
default (no compensation).  Screen only available when T1 or T2 is 
selected

.

 

 

Edit-Unit-Interface-RF-IF Port Impedance Screen 
 

 
Options:

 

 

50 Ohms 

 

75 Ohms 

Factory default:

 

50 Ohms 

 

 

Description:

 

Sets the IF port impedance.

 

G.703 line length: [133m]                
     1:133m     2:266m     3:399m        
     4:533m     5:655m

 

 

IF port impedance: [50 Ohms]             
               [50 Ohms]                 
         New: 50 Ohms     

 

 

Summary of Contents for Quantum



































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands