Panasonic KX-TPA73 Operating Instructions Manual Download Page 154

Page: 154 / 161

10.1.9 Troubleshooting

Problem

Possible Cause

Solution

The handset does
not work.

The battery is drained.

Charge the battery fully.
For details, see
9.2.3 Charging the Batteries,
page 114.

The power is off.

• Turn it on.

For details, see
2.12 Power On/Off
(KX-TPA70/KX-TPA73
only), page 57.

• Re-insert the battery, and

then set the handset on the
charger.
For details, see
9.2.1 Battery Installation,
page 113, and
9.2.3 Charging the
Batteries, page 114.

The handset/desk
phone does not
ring.

Ringer volume is set to
"Off".
(If the ringer volume is set
to "Off", is displayed.)

Adjust the ringer volume
level.
See 2.5 Adjusting the
Volume, page 49.

Silent Mode is on.
(If Silent Mode is on, the
icon is displayed.)

Turn off Silent Mode.
For details, see 4.5 Silent
Mode, page 70.

It is difficult to have
a conversation
when in Hands-free
mode.

The microphone is facing
the wrong direction or is
obstructed during the
conversation.

The front of the handset
should face you, and the
microphone should not be
covered.
For details, see
2.3.2 Handset
(KX-TPA70/KX-TPA73),
page 31.

10.1.9 Troubleshooting

154

Summary of Contents for KX-TPA73


































































































































































Search results

Summary of Contents for KX-TPA73

Reviews:

Related manuals for KX-TPA73

Brands by name

Popular brands

Panasonic KX-TPA73, Operating Instructions Manual

Search results

Summary of Contents for KX-TPA73

Reviews:

Related manuals for KX-TPA73

Brands by name

Popular brands