Panasonic KX-TPA73 Operating Instructions Manual Download Page 157

Page: 157 / 161

Problem

Possible Cause

Solution

While charging the
battery, the handset
and the AC adaptor
feel warm.

These are normal
conditions.

—

"No Service" is
displayed, and beep
tones are heard.

The handset/desk phone
is out of range.

Move closer to the base unit
or try again later.

The base unit or Server is
out of service.

Contact your phone system
dealer/ service provider.

The base unit is power off.

Turn on the power of the
base unit.

While charging the
battery, the LED
indicator blinks
rapidly, but the
handset does not
beep.

The temperature of the
battery being charged is
outside of normal limits.

Confirm that the area where
the handset is being
charged is between 5

℃

(41

℉

) and 40

℃

(104

℉

and wait for the battery’s
temperature to drop.

While charging the
battery, the LED
indicator blinks
rapidly and the
handset beeps
rapidly.

The battery is not
charging correctly due to
an electrical failure.

Unplug the AC adaptor from
the AC outlet, remove the
battery from the handset,
and contact your phone
system dealer/service
provider.

A wrong type of battery
such as Alkaline or
Manganese was inserted.

Use only the rechargeable
Ni-MH batteries (KX-TPA70
only) noted on page 19,
page 20.

I cannot remember
the PIN number.

—

Contact your phone system
dealer/ service provider.

10.1.9 Troubleshooting

157

Summary of Contents for KX-TPA73


































































































































































Search results

Summary of Contents for KX-TPA73

Reviews:

Related manuals for KX-TPA73

Brands by name

Popular brands

Panasonic KX-TPA73, Operating Instructions Manual

Search results

Summary of Contents for KX-TPA73

Reviews:

Related manuals for KX-TPA73

Brands by name

Popular brands