Panasonic KX-TPA73 Operating Instructions Manual Download Page 155

Page: 155 / 161

Problem

Possible Cause

Solution

You cannot make/
receive a call.

The handset is out of
range, or the base unit is
busy.

Move closer to the base unit
or try again later.

The radio channel is busy,
or a radio communication
error occurred.

Try again later.

The handset is not
registered to the base unit.

Register the handset to the
base unit. For details, see
9.4 Registering/
Deregistering a Handset/
Desk Phone to the
Panasonic base unit, page
117.

You cannot dial.

The number that you
dialed is restricted by your
phone system.

Consult your administrator
or your phone system
dealer/service provider.

Key lock mode is on.

To cancel the mode, press
and hold

for about 2

seconds.
For details, see 2.9 Key
Lock, page 54.

The radio channel is busy
or a radio communication
error occurred.

Try again later.

The handset stops
working during
operation.

An unknown error has
occurred.

• Turn the handset off, and

then turn it back on.
For details, see
2.12 Power On/Off
(KX-TPA70/KX-TPA73
only), page 57.

• Re-insert the battery and

try again.
For details, see
9.2.1 Battery Installation,
page 113.

10.1.9 Troubleshooting

155

Summary of Contents for KX-TPA73


































































































































































Search results

Summary of Contents for KX-TPA73

Reviews:

Related manuals for KX-TPA73

Brands by name

Popular brands

Panasonic KX-TPA73, Operating Instructions Manual

Search results

Summary of Contents for KX-TPA73

Reviews:

Related manuals for KX-TPA73

Brands by name

Popular brands