Panasonic KX-TPA73 Operating Instructions Manual Download Page 131

Page: 131 / 161

Incoming Option (difference when using a base unit other than the Panasonic base
unit)*1

Sub Item

Description

Setting

Default

Ringer Type

• External Ring

Select from Pattern 1–7
as the External Ring. Set
the Ringtone/LED/
Vibration for each
pattern.
[ ]/[ ]: Select desired
item.

Ringer Pattern

Ringtone 1–7

Pattern 1–7:
Ringtone 1–
7

LED Pattern

Red
Green
Orange
R→G→O

Pattern 1–7:
Red

Vibration pattern

Single
Double
Triple
Continuous

Pattern 1–7:
Single

Settings not shown above are the same as when connected to the Panasonic base

unit.

"Line" is displayed when using the Panasonic base unit.

Talk Option

Sub Item

Description

Setting

Default

Speaker Volume

Adjusts the rear speaker
volume.

Level 1–6

Level 3

Receiver
Volume

Adjusts the receiver
volume.

Level 1–6

Level 2

Headset Volume

Adjusts the headset
volume.

Level 1–6

Level 2

Headset Mic.
Vol

Adjusts the headset
microphone volume.

Level 1–6

Level 3

Noise Reduction

Activate/deactivate Noise
Reduction.

On
Off

Off

Talk On Charger

Selects whether to
continue the
conversation when the
handset is put on the
charger.

On
Off

Off

10.1.4 Phone Setting Menu Layout

131

Summary of Contents for KX-TPA73


































































































































































Search results

Summary of Contents for KX-TPA73

Reviews:

Related manuals for KX-TPA73

Brands by name

Popular brands

Panasonic KX-TPA73, Operating Instructions Manual

Search results

Summary of Contents for KX-TPA73

Reviews:

Related manuals for KX-TPA73

Brands by name

Popular brands