Panasonic KX-TPA73 Operating Instructions Manual Download Page 40

Page: 40 / 161

Suffix

Meaning

(none)/C

UK/AL/CE

Perform a transfer.

Perform an unscreened (blind) transfer.

*1*2*4

Private Hold

ABC2

Displayed when in Latin character entry mode.

0-9

Displayed when in Numeric character entry mode.

+ÀÂ

AÄÅ

Displayed when in Special character (Extended 1) entry
mode.

SŚŠ

Displayed when in Special character (Extended 2) entry
mode.

ΑΒΓ

Displayed when in Greek character entry mode.

Clears digits or characters.

Searches for an item in the contacts alphabetically.

AM/PM

Used to select AM or PM when setting the Memo Alarm
feature.

FLASH

Disconnects the current call and allows you to make
another call without hanging up.

Used to cancel the setting.

Activate/deactivate Noise Reduction.

Used to save a setting.

АБВ

Displayed when in Cyrillic character entry mode.

Used to set/clear the Auto Answer mode when in standby
mode. During a conversation, turns the microphone mute
feature on or off.

Fwd/DND

Used to set Call Forwarding and Do Not Disturb.

PARK

Used to retrieve a parked call (Call Parking).

*3*4

2.4.3 Soft Keys (KX-TPA70/KX-TPA73)

Summary of Contents for KX-TPA73


































































































































































Search results

Summary of Contents for KX-TPA73

Reviews:

Related manuals for KX-TPA73

Brands by name

Popular brands

Panasonic KX-TPA73, Operating Instructions Manual

Search results

Summary of Contents for KX-TPA73

Reviews:

Related manuals for KX-TPA73

Brands by name

Popular brands