Panasonic KX-TPA73 Operating Instructions Manual Download Page 112

Page: 112 / 161

9.1 Installation and Setup

Note

• Panasonic assumes no responsibility for injuries or property damage resulting from

failures arising out of improper installation or operation inconsistent with this
documentation.

WARNING

• To reduce the risk of fire or electric shock, do not overload AC outlets and extension

cords.

• Completely insert the AC adaptor/power plug into the AC outlet. Failure to do so may

cause electric shock and/or excessive heat resulting in a fire.

• Regularly remove any dust, etc. from the AC adaptor/power plug by pulling it from the

power outlet, then wiping with a dry cloth. Accumulated dust may cause an insulation
defect from moisture, etc. resulting in a fire.

9.2 Connections

KX-TGP700 (Base unit)

Connect the AC adaptor and the Ethernet cable to the base unit.

Hub

PNLV236xx

• Check the label color of the AC adaptor cord and the label color nearby DC jack of the

KX-TGP700. The color of the label must match the AC adaptor cord for the
KX-TGP700.

• If PoE is available, an AC adaptor is not needed.

• If you are using a PoE hub, the number of devices that you can connect simultaneously

is limited by the amount of power supplied by the hub.

9.1 Installation and Setup

112

Summary of Contents for KX-TPA73


































































































































































Search results

Summary of Contents for KX-TPA73

Reviews:

Related manuals for KX-TPA73

Brands by name

Popular brands

Panasonic KX-TPA73, Operating Instructions Manual

Search results

Summary of Contents for KX-TPA73

Reviews:

Related manuals for KX-TPA73

Brands by name

Popular brands