Panasonic KX-TPA73 Operating Instructions Manual Download Page 159

Page: 159 / 161

Error Message

Possible Cause

Solution

Memory Full

The Contacts is full and
cannot store the new item.

Remove unnecessary data
in the Contacts and try
again.

Need Repair

12: Li-ion battery failure
(KX-TPA73 only)

Contact your phone system
dealer/ service provider.

Not Found

The handset/desk phone
does not answer when a
call is made.

The handset/desk phone is
out of range or turned off.

Download Failed/
Upload Failed

There was a wireless
transmission error,
corrupted data, or the
memory became full
during a contacts
download.

• Remove unnecessary data

in the contacts, or consult
your administrator
regarding the number of
items being downloaded.

• Use the handset/desk

phone closer to the base
unit.

• This message disappears

if you access the contacts.

Mismatch
Firmware

The Software File Version
is not the latest version.

Update the Panasonic base
unit to the latest Software
File Version. For details,
consult your administrator.

10.1.10 Error Messages

159

Summary of Contents for KX-TPA73


































































































































































Search results

Summary of Contents for KX-TPA73

Reviews:

Related manuals for KX-TPA73

Brands by name

Popular brands

Panasonic KX-TPA73, Operating Instructions Manual

Search results

Summary of Contents for KX-TPA73

Reviews:

Related manuals for KX-TPA73

Brands by name

Popular brands