Panasonic KX-TPA73 Operating Instructions Manual Download Page 113

Page: 113 / 161

• The initial setting for the KX-TGP700 IP address is "DHCP—Auto". For information

about your network environment, contact your administrator. For details, see Network
Settings, page 145.

Charger for KX-TPA70/KX-TPA73

Connect the AC adaptor to the charger.

PQLV219xx

• Check the label color of the AC adaptor cord and the label color nearby DC jack of the

charger. The color of the label must match the AC adaptor cord for the charger.

• The AC adaptor should be connected to a vertically oriented or floor-mounted AC

outlet. Do not connect the AC adaptor to a ceiling-mounted AC outlet, as the weight of
the adaptor may cause it to become disconnected.

• Fasten the AC adaptor cord to the cord holder.

• Use only the included Panasonic AC adaptor.

9.2.1 Battery Installation

Open the battery cover, insert the batteries, and close the cover as indicated below.
For KX-TPA70

For KX-TPA73

9.2.1 Battery Installation

113

Summary of Contents for KX-TPA73


































































































































































Search results

Summary of Contents for KX-TPA73

Reviews:

Related manuals for KX-TPA73

Brands by name

Popular brands

Panasonic KX-TPA73, Operating Instructions Manual

Search results

Summary of Contents for KX-TPA73

Reviews:

Related manuals for KX-TPA73

Brands by name

Popular brands