Panasonic KX-TPA73 Operating Instructions Manual Download Page 49

Page: 49 / 161

2: Call Forward

*1*2

(page 80)

Displays and/or sets Call Forwarding.

3: Flash/Recall (page 60)

Disconnects the current call and allows you to make another call without hanging up.

4: Conference (page 76)

Establishes a multiple-party conversation.

5: BT On/Off

Sets the BT communication On/Off control.

6: Call History (page 50)

Makes a call using the Call History.

7: Call Park

(page 75)

Used to park or retrieve a call in a preset parking zone.

8: Paging

(page 64)

Makes a voice announcement to the handsets simultaneously.

9: Redial (page 61)

Redials the last dialed number.

0: Pause

Pauses when dialing.

: Auto Answer

Answers an incoming call automatically in Hands-free mode.

#: Contacts (page 84)

Makes a call using the Contacts.

KX-TPA70/KX-TPA73 only

"Call Forward" when connected to a base unit other than the Panasonic base unit.

This item is displayed only when it is enabled in settings. Contact your administrator

for further information.

2.5 Adjusting the Volume

Adjusting the Receiver/Speaker/Headset Volume

During a conversation, press [ ], [ ], [Vol.Up], or [Vol.Down] to adjust the volume (Level
1–6).

Adjusting the Ringer Volume or Turning the Ringer Off

[In standby mode]

/[CENTER]

2.5 Adjusting the Volume

Summary of Contents for KX-TPA73


































































































































































Search results

Summary of Contents for KX-TPA73

Reviews:

Related manuals for KX-TPA73

Brands by name

Popular brands

Panasonic KX-TPA73, Operating Instructions Manual

Search results

Summary of Contents for KX-TPA73

Reviews:

Related manuals for KX-TPA73

Brands by name

Popular brands