manualshive.com logo in svg

Panasonic GA-ML Series, Manual

Share
Download
Panasonic GA-ML Series Manual Download Page 45

43

3 System

  3.7.3 PoE Schedule Configuration    

Click 

Apply

 to reflect the change.

Date

 

List Index 

This parameter displays the number regarding the date 
list where the PoE schedule is conducted. 

PoE Action

This parameter displays an action of the PoE schedule. 

The options available are 

OFF, ON

 and 

OFF/ON

.

Order By

This parameter configures the sequence of displaying 
the PoE schedule. The options available are 

Index

 and 

Next Execution Time

.

Filter

 

by Interface

This parameter filters with the interface where 
displaying the PoE scheduler is selected.

Parameter

Overview 

Summary of Contents for GA-ML Series

















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands