manualshive.com logo in svg

Panasonic GA-ML Series, Manual

Share
Download
Panasonic GA-ML Series Manual Download Page 238

236

8 ACL (Access Control List)

 8.1.2 

IPv4   

                    You can configure the following parameters. 

Parameter 

Overview 

Sequence Number

Enter the ACL rule number. The range is from 1 to 
65,535. If you choose 

Auto Allocation

, the ACL rule 

number regarding this entry is automatically generated. 

Protocol Type

Choose the protocol type option. The options available 
are 

TCP

, 

UDP

, 

ICMP

, 

EIGRP

 (88), 

ESP

 (50), 

GRE

 (47), 

IGMP

 (2), 

OSPF

 (89), 

PIM

 (103), 

VRRP

 (112), 

IP-in-IP

 

(94), 

PCP

 (108), 

Protocol ID

 and 

None

.

•

Value 

- You can enter the protocol ID, manually. The 

range is from 0 to 255.  

•

Mask 

- After choosing the 

Protocol ID

 option, enter 

the value of the protocol mask, manually. The range 
is from 0x0 to 0xFF. 

•

Fragment

 - If you choose this option, the packet 

fragment filtering is included. 

Source

Choose and enter the source information. The options 
available are as follows.

•

Optional

 - Evaluates optional source traffics 

according to this rule condition.

•

Host 

- Uses and enters an IP address of source host. 

•

IP

 - Use the bit-map of

 Wildcard

, and then use and 

enter a group of the source IP address. The bit 
corresponding to the bit-value of 1 is ignored, but 
the bit corresponding to the bit-value of 0 is 
checked.

Destination

Choose and enter the destination information. The 
options available are as follows.

•

Optional

 - Evaluates the optional destination traffic 

according to this rule condition.

•

Host

 - Uses and enters an IP address of a destination 

host.

•

IP

 - Use the bit-map of

 Wildcard

, and then use and 

enter a group of the destination IP address. The bit 
corresponding to the bit value of 1 is ignored, but 
the bit corresponding to the bit value of 0 is checked.

Summary of Contents for GA-ML Series

















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands