manualshive.com logo in svg

Panasonic GA-ML Series, Manual

Share
Download
Panasonic GA-ML Series Manual Download Page 263

261

8 ACL (Access Control List)

  8.2.4 Extended IPv6 ACL    

Destination Port

Choose and enter the destination-port value. The 
options available are as follows.

•

=

 - The ACL uses the port-number specified.

•

>

 - The ACL uses all the ports, which are greater than 

the port number specified.

•

<

 - The ACL uses all the ports, which are smaller than 

the port number specified.

•

≠

 - The ACL uses all the ports except for the port-

number.

•

Range

 - The ACL uses the ports specified, within the 

range.

•

Mask

 - The ACL uses the ports, within the range of 

the mask specified. Enter the port mask value in the 
space provided. The range is from 0x0 to 0xFFFF.

• This parameter is available when you select 

TCP 

or 

UDP

 as the protocol type.

TCP Flag

Select the TCP flag, which is evaluated in this ACL. The 

options available are 

ack

, 

fin

, 

psh

, 

rst

, 

syn

 and 

urg

. 

This parameter is available when you select 

TCP

 as the 

protocol type.

Specify ICMP
Message Type

Choose the

 ICMP Message Type

 to use. This 

parameter is available when you select 

ICMP

 as the 

protocol type.

ICMP Message Type

When the 

ICMP Message Type 

is not specified, enter 

the ICMP message type numerical-value used here. The

range is from 0 to 255. When you select the 

ICMP 

Message Type

, this numerical value is automatically 

entered. This parameter is available when you select 

ICMP

 as the protocol type.

Message Code

When the 

ICMP Message Type 

is not selected, enter 

the message code numerical-value (to use). The range is 

from 0 to 255. When you select the 

ICMP Message 

Type

, the value is automatically entered. This 

parameter is available when you select 

ICMP

 as the 

protocol type.

Parameter

Overview

Summary of Contents for GA-ML Series

















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands