manualshive.com logo in svg

Panasonic GA-ML Series, Manual

Share
Download
Panasonic GA-ML Series Manual Download Page 169

167

5 L2  Features

  5.8.5 LLDP Dot1 TLV Settings    

5.8.5

LLDP Dot1 TLV Settings

Use the following window to implement the settings on IEEE 802.1 LLDP 

TLV and display its settings.

 

Choose 

L2 Features > LLDP > LLDP Dot1 TLV Settings 

to display the 

following window.

Figure 5-65 LLDP Dot1 TLV Settings

In the section of

 LLDP Dot1 TLV Settings

, you can configure the 

following parameters. 

 

Parameter 

Overview 

From Port/ To Port

Choose the port you use.

Port VLAN 

This parameter enables or disables to transmit Port 
VLAN ID TLV.

Protocol VLAN 

This parameter enables or disables to transmit the port 
and protocol VLAN ID (PPVID) TLV. Enter the ID in the 
entry field provided.  

VLAN Name

This parameter enables or disables to transmit the TLV 
of a VLAN name. Enter a VLAN ID in the entry field 
provided.

Protocol Identity

This parameter enables or disables to transmit the 
protocol identity TLV. The options available are

 None

,

 

EAPOL

,

 LACP

,

 GVRP

,

 STP

 and

 All

,

 

as a protocol name 

Summary of Contents for GA-ML Series

















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands