manualshive.com logo in svg

Panasonic GA-ML Series, Manual

Share
Download
Panasonic GA-ML Series Manual Download Page 267

265

8 ACL (Access Control List)

 8.2.5 

Extended 

MAC 

ACL   

Click 

Apply

 to add a new ACL rule.

Click 

Back

 to return to the ACL access list window.

Ethernet Type

Enter the Ethernet type as the hexadecimal value. The 

range is from 0x600 to 0xFFFF. If you choose the 

optional Ethernet type profile from the drop-down list 

of 

Specify Ethernet Type

, the appropriate 

hexadecimal-value is automatically displayed.

Ethernet Type Mask

 

Enter the Ethernet type mask as the hexadecimal value. 

The range is from 0x0 to 0xFFFF. If you choose an 

optional Ethernet type profile from the drop-down list 

of 

Specify Ethernet Type

, the appropriate 

hexadecimal-value is automatically displayed.

CoS

Choose the CoS-value; the range is from 0 to 7.

•

Mask

 - Enter the value of CoS mask. The range is 

from 0x0 to 0x7.

VID

Enter one VLAN ID to use. The range is from 1 to 4,094.

•

Mask

 - Enter the value of VLAN ID mask. The range 

is from 0x0 to 0xFFF.

Time Range

Enter the name of the time range profile to use in this 
ACL rule. The number of characters for the name can be 
up to 32.

Parameter

Overview

Summary of Contents for GA-ML Series

















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands