manualshive.com logo in svg

Panasonic GA-ML Series, Manual

Share
Download
Panasonic GA-ML Series Manual Download Page 294

292

9 Security

  9.2.5 EAP Port Config    

9.2.5

EAP Port Config 

Use the following window to implement the EAP settings on the port 

specified and display its settings.  

Choose 

Security > 802.1X > EAP Port Config

 to display the following 

window.

Figure 9-10 EAP Port Config

You can configure the following parameters. 

Click 

Apply

 to check the content changed.

Parameter

Overview

From Port/ To Port

Choose the port you use.

EAP Request 

This parameter enables or disables a function of EAP 
requests on the port specified. 

EAP Forward

This parameter enables or disables a function of EAP 
forward on the port specified. You can use it to enable 
or disable the forwarding of IEEE 802.1X Protocol Data 

Units (PDU).

 

Summary of Contents for GA-ML Series

















































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands