Panasonic GA-ML Series Manual Download Page 314

Page: 314 / 496

312

9 Security

9.3.8

Accounting

Settings

Click

Apply

to check the content changed.

Click

AAA Accounting Exec

tab to display the following window.

Figure 9-26 Accounting Settings (AAA Accounting Exec)

In the section of

AAA Accounting Exec

, you can configure the following

parameters.

Click

Apply

to add a new entry.

Click

Delete

to delete the entry specified.

Click the

AAA Accounting Command

tab to display the following

window.

Method 1 - Method 4

Choose the method list to use for this configuration.The
options available are

None

Group

RADIUS

and

The

None

option is available for the method

Parameter

Overview

Parameter

Overview

List Name

Enter a method-list name to use in the

AAA

Accounting Exec

option.

Method 1 - Method 4

Choose a method list to use for this configuration. The
options available are

None

Group

RADIUS

and

The

None

option is available for the method

1, only.

Summary of Contents for GA-ML Series

















































































































































































































































































































































































































































































































Search results

Summary of Contents for GA-ML Series

Reviews:

Brands by name

Popular brands

Panasonic GA-ML Series, Manual

Search results

Summary of Contents for GA-ML Series

Reviews:

Brands by name

Popular brands